Plumbing Basics: An Essential for Installing a Bathtub
Plumbing Basics: An Essential for Installing a Bathtub
Blog Article
What are your opinions regarding How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't specifically rocket science, but it does need solid plumbing, carpentry, and often, tiling skills. Changing an old tub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently accessible, the task can move rapidly; if you need to open a wall surface to eliminate the old bathtub and also place the new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old bathtub and also embeded in the brand-new one. Make sure you have certified on your own for the task and also are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed task, it is better to think about using one prior to you begin. Chances are you might need a professional plumber to make tube links.
This post will help you set up a brand-new bath tub in your restroom if you have actually already gotten a brand-new tub and also do not need to transform the arrangement of your previous water system pipes.
Your tools as well as product list must consist of the following:
Preparing for the Installment
First of all, the supporting framework provided with the bath needs to be fitted (if required) according to the producer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the flexible faucet ports to the bottom of both faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is separate the water supply. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic due to the limited access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a fabric ready for the staying water that will certainly come from the pipelines. When the supply pipes have been eliminated, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
Before moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, position the bath tub in the required position. The wooden boards are valuable in evenly spreading the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub until the level reviews level.
To set up taps, fit all-time low of the furthest adaptable faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water supply as well as inspect all joints and brand-new pipework for leakages and also tighten them if essential. Fill the bathtub and additionally inspect the overflow electrical outlet and also the typical outlet for leaks.
Lastly, deal with the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the tub should wait until the tub has actually been used at the very least once as this will settle it right into its last position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in place in between the tap and the sink. Safeguard the tap in position with the supplier provided backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former type should be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture a rigid seal, causing the water to pass through the wall surface in between the bath as well as the tiling, bring about issues with moisture as well as possible leakages to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can crack rather early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the market. It is advisable to fit the ceramic tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that write up about A Step-by-Step Guide to Installing a Bathtub when doing research the search engines. In case you enjoyed reading our page kindly make sure you remember to pass it around. Bless you for your time. Come back soon.
Expertly handling plumbing emergencies daily. Report this page